INON

■MRS Control Ring (60/60II/100 UII/100UIII/50 for Olympus)

click to enlarge

Optional accessory to upgrade the "MRS50 Port (w/o control ring) for Olympus" to "MRS50 Port for Olympus (with MRS Control Ring)" for manual focus operation. Optional "MRS Magnet Ring 50 Set for Olympus" is necessary.
 
■Weight: 129g (4.6oz) [air] / 47g (1.7oz) [underwater]

■Shade Sponge D80

click to enlarge

When using "Olympus ZUIKO DIGITAL ED 8mm F3.5 Fisheye" in "Dome Port for Olympus", this sponge is attached on inner surface of the port to block built-in / bundled flash light not to be exposed on an image.
 
■Compatible Port
Dome Port + Shade 2 Set for Olympus, Dome Port for Olympus
 
■Compatible Waterproof Protector
Olympus PT-EP08 (Mirrorless Camera OM-D E-M5)
Olympus PT-EP11 (Mirrorless Camera OM-D E-M1)
Olympus PT-EP14 (Mirrorless Camera OM-D E-M1 Mark II)

■Shade 2 Only

Shade 2 Only

The INON Shade 2 is attached on INON Dome Port series to prevent accidental damage on port lens and also blocks unnecessary light to obtain clear image.
Attaching the Shade 2 is highly recommended since it enables you to place the combined housing port lens side down when setting a camera etc.
 
■Weight: 82.0g (2.9oz) [air]
 
■Material: Polycarbonate
 
■Compatible Port
Dome Port + Shade 2 Set for Olympus, Dome Port for Olympus, Dome Port 2 + Shade 2 Set, Dome Port 2

■Double Hole Rubber Bush for Fiber Optics

click to enlarge

The Double Hole Rubber Bush for Fiber Optics directly holds INON "Optical D Cable" product on compatible underwater housing including Olympus genuine water-proof protector with an optical cable connector.
 
■Compatible Waterproof Protector
Olympus PT-E05 (Digital SLR E-520)
Olympus PT-E06 (Digital SLR E-620)
Olympus PT-EP01 (Mirrorless Camera PEN E-PL1)
Olympus PT-EP03 (Mirrorless Camera PEN E-PL2)
Olympus PT-EP05L (Mirrorless Camera PEN E-PL3)
Olympus PT-EP06L (Mirrorless Camera PEN E-PM1)
Olympus PT-EP08 (Mirrorless Camera OM-D E-M5)
Olympus PT-EP10 (Mirrorless Camera PEN E-PL5)
Olympus PT-EP11 (Mirrorless Camera OM-D E-M1)
Olympus PT-EP12 (Mirrorless Camera PEN E-PL7)
Olympus PT-EP13 (Mirrorless Camera OM-D E-M5 Mark II)
Olympus PT-EP14 (Mirrorless Camera OM-D E-M1 Mark II)
 
*Set camera [RC Mode] to OFF when using Optical D Cable product to connect an INON strobe and E-PL1, E-PL2, E-PL3, E-PM1, E-M5, E-PL5, E-M1, E-PL7, E-M5 Mark II or E-M1 Mark II.

■Rubber Bush Type L

Rubber Bush Type L

The Rubber Bush Type L directly holds INON "Optical D Cable" product on compatible underwater housing including Olympus genuine water-proof protector with an optical cable connector. Best suited for an underwater housing with a fiber optics connector located on its front.
 
■Compatible Waterproof Protector
Olympus PT-E05 (Digital SLR E-520)
Olympus PT-E06 (Digital SLR E-620)
Olympus PT-EP01 (Mirrorless Camera PEN E-PL1)
Olympus PT-EP03 (Mirrorless Camera PEN E-PL2)
Olympus PT-EP05L (Mirrorless Camera PEN E-PL3)
Olympus PT-EP06L (Mirrorless Camera PEN E-PM1)
Olympus PT-EP08 (Mirrorless Camera OM-D E-M5)
Olympus PT-EP10 (Mirrorless Camera PEN E-PL5)
Olympus PT-EP11 (Mirrorless Camera OM-D E-M1)
Olympus PT-EP12 (Mirrorless Camera PEN E-PL7)
Olympus PT-EP13 (Mirrorless Camera OM-D E-M5 Mark II)
Olympus PT-EP14 (Mirrorless Camera OM-D E-M1 Mark II)
 
*Set camera [RC Mode] to OFF when using Optical D Cable product to connect an INON strobe and E-PL1, E-PL2, E-PL3, E-PM1, E-M5, E-PL5, E-M1, E-PL7, E-M5 Mark II or E-M1 Mark II.

■Main Base III

JAN code:4562121439160

 
MainBaseIII
 

A base plate attached on the bottom of an underwater housing to add a handle. As pre-installed two tripod screws are adjustable within center-to-center distance 33-105mm/1.3-4.1inch, it widely supports from compact housing to large SLR housing enabling you to use the same base plate when you change camera system.
 
■Weight: [air] 134g/4.7oz, [underwater] approx.82g/2.9oz

■Holder III

JAN code:4562121439177

HolderIII
 

When holding an underwater housing directly by hand, the Holder III supports the back of your hand. The top end is designed to attach wide range of INON Arm System products.
 
■Weight: [air] 156g/5.5oz, [underwater] approx.80g/2.8oz

■Holder III Set

JAN code:4562121439184

HolderIIISet

Unlike previous Holder II, the Holder III can be attached on both sides of an underwater housing and top end has total four fixing screw holes comparing to two of Holder II. The Holder III can be installed with three different angles (Holder III attached on the Main Base III at the right angle may interrupt proper opening/closure of combined underwater housing. If this happens, remove the Main Base III with Holder III(s) from the housing to open/close the housing.) Compatible with the Panhead Adapter packaged with the UW 3-Way Panhead.
 
■Set contents
Maine Base III, Holder III
 
■Weight: [air] 290g/10.2oz, [underwater] approx.162g /5.7oz
 
 

Page Top

■Shoe Base

Shoe Base

■Shoe Base 1/4-20UNC

Shoe Base 1/4-20UNC

■Shoe Base M6

Shoe Base M6

■Shoe Base BALL

Shoe Base BALL
Adapter bases to install INON strobe, LED flashlight or action camera directly on accessory shoe of an underwater housing.
 
■Weight
Shoe Base: 41g (1.4oz) [air] / approx.20g (0.7oz) [underwater]
Shoe Base 1/4-20UNC: 78g (2.8oz) [air] / approx.45g (1.6oz) [underwater]
Shoe Base M6: 69g (2.4oz) [air] / approx.40g (1.4oz) [underwater]
Shoe Base BALL: 52g (1.8oz) [air] / approx.28g (1.0oz) [underwater]
 
■Compatible Underwater Housing
Olympus PT-E05 (Digital SLR E-520)
Olympus PT-E06 (Digital SLR E-620)
Olympus PT-EP01 (Mirrorless Camera PEN E-PL1)
Olympus PT-EP03 (Mirrorless Camera PEN E-PL2)
Olympus PT-EP05L (Mirrorless Camera PEN E-PL3)
Olympus PT-EP06L (Mirrorless Camera PEN E-PM1)
Olympus PT-EP08 (Mirrorless Camera OM-D E-M5)
Olympus PT-EP10 (Mirrorless Camera PEN E-PL5)
Olympus PT-EP11 (Mirrorless Camera OM-D E-M1)
Olympus PT-EP12 (Mirrorless Camera PEN E-PL7)
Olympus PT-EP13 (Mirrorless Camera OM-D E-M5 Mark II)
Olympus PT-EP14 (Mirrorless Camera OM-D E-M1 Mark II)
 
*When installing a strobe / LED flashlight via INON Shoe Base on the Olympus PT-EP01, total camera system will have about 100g buoyancy. It is recommended to use a balance weight to have negative buoyancy for the sake of safety.
 
*When installing a strobe via INON Shoe Base on the Olympus PT-EP06L, total camera system will have about 20g buoyancy. It is recommended to use a balance weight to have negative buoyancy for the sake of safety.
 
 
set-up images
set-up images
set-up images

■Dome Port Cover L

Dome Port Cover L
Set-up image

Set-up image

The Dome Port Cover L is made of neoprene as same as wet suits and designed to fit toφ180mm/7.1in dome. It is recommended to cover compatible dome lens/port all the time to prevent accidental damage unless shooting images. The Dome Port Cover L has slits on its top and bottom to help easy and speedy installation/removal on a dome lens/port equipped with a hood.
 
■Compatible Port
Dome Port + Shade 2 Set for Olympus,Dome Port for Olympus,
Dome Port 2 + Shade 2 set, Dome Port 2
 

*Never put wet lens cover on compatible lens/port on land. Doing so may cause degradation of the lens coating or glass itself resulting in spotting or discoloration.

■Dome Port Cover S

Dome Port Cover S
Set-up image

Set-up image

The Dome Port Cover S is made of neoprene as same as wet suits and designed to fit toφ115mm/4.5in dome. It is recommended to cover compatible dome lens/port all the time to prevent accidental damage unless shooting images. The Dome Port Cover S has slits on its top and bottom to help easy and speedy installation/removal on a dome lens/port equipped with a hood.
 
■Compatible Port
Dome Port EP02 for Olympus, Dome Port EP01 for Olympus,
Dome Port 115, Front Port Dome 115
 
■Compatible Attachment Lens
Dome Lens Unit II for UWL-H100, Dome Lens Unit II for UWL-100,
Dome Lens Unit for UWL-100
 

*Never put wet lens cover on compatible lens/port on land. Doing so may cause degradation of the lens coating or glass itself resulting in spotting or discoloration.

■Snap-on Lens Cap M67

click to enlarge
Set-up image

Set-up image

The Snap-on Lens Cap M67 is a plastic lens cap for close-up lenses and digital SLR housing lens ports to protect front optical element. Spring loaded center tabs provide easy installation and removal only by squeezing the tabs. Packaged lanyard to avoid loss of the lens cap when not being attached on a lens/port.