Lens Hood III
JAN/EAN code : 4570018120251
A lens hood for the UWL-H100/UWL-95 C24/UWL-95S XD wide conversion lenses. Using the Lens Hood III can block unnecessary light coming from outside of combined lens coverage to suppress flare/ghosting likely happen when shooting in backlight. Also attaching the Lens Hood III can protect lens surface and lens frame from accidental damage.
No vignetting at wide end both on land and underwater when installing the Lens Hood III on the UWL-95 C24 series lens.
*Confirmed camera housings
Sony MPK-URX100A, Olympus PT-059, PT-058, PT-056
Please note that other housings have not been confirmed by INON and may have vignetting depending on combination and condition.
Outer diameter : φ114 mm/4.5 in
Length : 53 mm/2.1 in
Weight : [air] 54 g/1.9 oz, [underwater] approx.8 g/0.3 oz
*Not usable together with "Dome Lens Unit III".
M67 Type1 Screw Ring for UWL-95 C24
JAN/EAN code : 4562121439764
A set of a threaded mount ring for the UWL-95 C24 M67 Type1 and fixing screws to replace with worn original screw ring or to convert screw ring from Type2 to Type1. Also installing this screw ring on the UWL-95 C24 M52 will convert the lens to UWL-95 C24 M67 Type1.
If you have any difficulty to remove original fixing screw(s) due to salt build-up etc, do not proceed any further and consult your purchasing dealer for advice.
M67 Type2 Screw Ring for UWL-95 C24
JAN/EAN code : 4562121439771
A set of a threaded mount ring for the UWL-95 C24 M67 Type2 and fixing screws to replace with worn original screw ring or to convert screw ring from Type1 to Type2. Also installing this screw ring on the UWL-95 C24 M52 will convert the lens to UWL-95 C24 M67 Type2.
If you have any difficulty to remove original fixing screw(s) due to salt build-up etc, do not proceed any further and consult your purchasing dealer for advice.
Compatible camera system (as of April, 2020)
A housing with a lens port of 6 mm/0.2 inch or less distance between lens port edge and lens port surface.
M52 Lens Holder for Float Arm (for UWL-95 C24 M52)
JAN/EAN code : 4562121439757
A lens holder attached on a Float Arm/Mega Float Arm/Mega Float Tube or on the M5 Joint installed on a Stick Arm/Multi Ball Arm to carry M52 series attachment lens. This lens holder can carry the UFL-M150 ZM80 Underwater Micro Fisheye Lens attached on the M27-M67 Mount Converter for UFL-M150 ZM80/Step-up Ring 52-67 as well.
Weight : [Air] 49 g/1.7 oz, [Underwater] approx. 26 g/0.9 oz
Compatible arm/base
Float Arm S/M/ML
Mega Float Arm S/M
Mega Float Tube S/M
M5 Joint installed on Stick Arm SS-T/S-T/M-T/L
M5 Joint installed on Multi Ball Arm ML/L/LL/XL
M52 Lens Holder S (for UWL-95 C24 M52)
JAN/EAN code : 4562121439733
A lens holder attached on an INON Arm, D Holder Extension Bar or Grip Base DIII with Rubber Grip to carry M52 series attachment lens. This lens holder can carry the UFL-M150 ZM80 Underwater Micro Fisheye Lens attached on the M27-M67 Mount Converter for UFL-M150 ZM80/Step-up Ring 52-67 as well.
Weight : [Air] 54 g/1.9 oz, [Underwater] approx. 28 g/1.0 oz
Compatible arm/base
Arm SS/S/M/L
YS Arm MS/M
Grip Base DIII with Rubber Grip D
Grip Base DII with Rubber Grip D
D Holder Extension Bar installed on Grip Base D4/Grip Base M1/D Holder
M52 Lens Holder W (for UWL-95 C24 M52)
JAN/EAN code : 4562121439740
A lens holder attached on an INON Arm to carry maximum two of M52 series attachment lenses. The lens holder is installed on an INON Arm sandwiched between Lens Holder [screw] and Lens Holder [hole] of this product. The Lens Holder [screw] is usable as M52 Lens Holder S and the Lens Holder [hole] is usable as M52 Lens Holder for Float Arm. This lens holder can carry the UFL-M150 ZM80 Underwater Micro Fisheye Lens attached on the M27-M67 Mount Converter for UFL-M150 ZM80/Step-up Ring 52-67 as well.
Weight* : [Air] 104 g/3.7 oz, [Underwater] approx. 50 g/1.8 oz
*Whole component
Compatible arm/base
1.When installing both lens caddies
Arm SS/S/M/L
YS Arm MS/M
2.When using Lens Holder [screw] as M52 Lens Holder S
Arm SS/S/M/L
YS Arm MS/M
Grip Base DIII with Rubber Grip D
Grip Base DII with Rubber Grip D
D Holder Extension Bar installed on Grip Base D4/Grip Base M1/D Holder
3.When using Lens Holder [hole] as M52 Lens Holder for Float Arm
Float Arm S/M/ML
Mega Float Arm S/M
Mega Float Tube S/M
M5 Joint installed on Stick Arm SS-T/S-T/M-T/L
M5 Joint installed on Multi Ball Arm ML/L/LL/XL
Lens Holder for Float Arm (for UWL-95 C24 M67)
JAN/EAN code : 4562121434127
A lens holder attached on Float Arm/Mega Float Arm or on the M5 Joint installed on Stick Arm/Multi Ball Arm to carry M67 series/28M67 series attachment lens to help comfortable multiple lens handling underwater.
Lens Holder S (for UWL-95 C24 M67)
JAN/EAN code : 4562121431713
A lens holder attached on an Arm, D Holder Extension Bar etc. to carry M67 series/28M67 series attachment lens to help comfortable multiple lens handling underwater.
Lens Holder W (for UWL-95 C24 M67)
JAN/EAN code : 4562121431720
A lens holder attached on an Arm, D Holder Extension Bar etc. to carry M67/28M67 series attachment lens. Compatible product is sandwiched between Lens Holder [screw] and Lens Holder [hole], or Lens Holder [screw] and Lens Holder Base of this product. The Lens Holder [hole] is usable as like M67 Lens Holder for Float Arm as well.
Front Cover 110 (for UWL-95 C24 M67/UWL-95 C24 M52)
JAN/EAN code : 4562121438989
A cover designed for UWL-95 C24 M67/UWL-95 C24 M52 fitted with the Lens Hood II. This cover protect lens surface when not in use as the cover is made of elastic neoprene material.
UWL-100 Neoprene Carry Pouch (for UWL-95 C24 M67/UWL-95 C24 M52)
JAN/EAN code : 4562121431645
A carry pouch made of neoprene which is used for wet suit and can be brought to underwater. It is recommended to put attachment lens in this carry pouch whenever not in use to prevent accidental damage.
*Not usable when the Lens Hood III or Dome Lens Unit III is attached on the lens.
