Enables to attach a lanyard on INON X-2 for EOS6D, X-2 for EOS70D or X-2 for EOS80D VC.Arc-like elongate slots allow to adjust orientation of eyelets.The plate can accommodate with wide range of housing adapters.Packaged grommets can contribute to avoid annoying rattle sounds when filming movie as well as not to damage on a housing by metal rings of the lanyard.
 
 
Weight: [air] 52 g/1.8 oz. [underwater] approx.42 g/1.5 oz. 
 
Compatible X-2 series Housing (*1)
X-2 for EOS6D, X-2 for EOS70D, X-2 for EOS80D VC

 
Compatible Arm System Products (*2)
Multi Direct Base IIa
Multi Direct Base II WB
Multi Direct Base II Long
Shoe Base Adapter X-2 + Shoe Base II
M6 Plate Direct Base III+ Direct Base III
M6 Plate Direct Base III+ Direct Base YS RT

 

(*1) It is possible to attach this product to X-2 for EOS10D, X-2 for EOS20D, X-2 for EOS30D, X-2 for EOS50D/40D or X-2 for EOS60D but it requires to remove pre-installed　"Lanyard hook". Please consult with your purchasing dealer. Not compatible with an INON housing which has done "Sync Connector Installation".
(*2) Attaching Clamp III, Z Joint or Light Holder products may interfere full movement of the lanyard. 

A spacer designed to attach the Holder III directly on the right side of the INON X-2 housing to benefit with less weight if left hand grip is not required. INON Arm System is directly attachable on the top end of the Holder III.
 
Weight: [air] 48 g/1.7 oz. [underwater] approx.31 g/1.1oz  *standalone
              [air] 236 g/8.3 oz. [underwater] approx.79 g/2.8 oz  *with Holder III

A base plate attached on the bottom of an underwater housing to add a handle. As pre-installed two tripod screws are adjustable within center-to-center distance 33-105mm/1.3-4.1inch, it widely supports from compact housing to large SLR housing enabling you to use the same base plate when you change camera system.
 
Weight: [air]134 g/4.7 oz. [underwater] approx.82 g/2.9 oz.

When holding an underwater housing directly by hand, the Holder III supports the back of your hand. The top end is designed to attach wide range of INON Arm System products.
 
Weight: [air] 156 g/5.5 oz. [underwater] approx.80 g/2.8 oz.

An adapter to attach the Shoe Base on top of the X-2 series housing or Grip Bar III Set enabling to hold Z-330/D-200/S-2000/Z-240/D-2000 strobe or LE series LED flashlight combined with Z Joint or Light Holder product to have compact yet flexible lighting.
 
Weight: [air]10 g/0.4 oz. [underwater] approx. 6 g/0.2 oz.
 
Compatible [X-2] series Housing
X-2 for EOS10D, X-2 for EOS10D BK, X-2 for EOS20D, X-2 for EOS20D BK
X-2 for EOS20D BK(TM), X-2 for EOS30D BK(TM), X-2 for EOS50D/40D
X-2 for EOS60D, X-2 for EOS70D, X-2 for EOS6D, X-2 for EOS80D VC,
X-2 for GF1, X-2 for GF2
 
Compatible Arm System Products
Grip Bar III Set, Holder II Grip Set, Holder Base, Grip Bar Set, Grip Bar II Set
 

*The thumbscrew of the Z Joint or Light Holder could possibly obstruct free movement of an Optical D Cable product or electrical cable attached on X-2 housing series.

 
Compact and lightweight straight type viewfinder supporting full frame DSLR.Using a large prism to minimize light attenuation makes it possible to see every corner of camera’s viewfinder image clearer and brighter despite of eye position. Unlike conventional viewfinders, this bright viewfinder enables you to focus precisely and comfortably even in dark underwater. Optically designed to suit to an electrical viewfinder (EVF) of a DSLR camera which provides wider viewing angle, so no vignetting nor blur even in corners.Magnification of this viewfinder is same as camera’s viewfinder. As its eye-point underwater is extended to 60 mm/2.4 inch, no vignetting of viewfinder image even through a mask.Viewfinder body is made from corrosion resistant aluminum and fiber reinforced plastic (FRP) to make the body compact, lightweight yet durable.
 
*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included when purchasing this product only.
 
Weight: [air] 305 g/10.7 oz. 

 

The 45°Viewfinder is an interchangeable finder unit to extend eye-point of camera's viewfinder without changing image size (x1.0) to see all finder image area even through a mask without vignetting. The eye piece is at 45 degree angle to camera's optical axis which helps to shoot lower subject like a goby on seabed. Also the eye piece is 360 degree rotatable making it easy to shoot vertical composition from low angle.
 
*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included when purchasing this product only.
 
Weight: [air] 337 g/11.9 oz. 

Optional accessory for Straight Viewfinder Unit II for X-2 and 45º View Finder Unit II for X-2.Add-on correction lens to shift +1.5 diopter for those who are unable to adjust with camera’s viewfinder diopter adjustment range due to long sight or presbyopia.The Diopter Correction Lens is to be installed before diving by dropping it inside of the Straight Viewfinder Unit II from housing side and tighten it by packaged tool (not changeable underwater).
 
Weight: [air] 2 g/0.07 oz. 

 

The Straight Viewfinder Unit for X-2 is an interchangeable finder unit to extend eye-point of camera's viewfinder without changing image size (x1.0) to see all finder image area even through a mask without vignetting.
The eye piece is level to camera's optical axis to position camera/housing closer to a subject without changing your position.
 
The Straight Viewfinder Unit for X-2 is designed and manufactured based on a focusing screen of compatible camera to make it as compact as possible. So camera setting information displayed below the focusing screen may get dark
and hard to read.
 
*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included when purchasing this product only.
 
Weight: [air] 277 g/9.8 oz.

 

The Pick-up Finder Unit 2 for X-2 is a compact and high-performance interchangeable finder unit to extend eye-point and scale down image size (x0.75) to practically suppress vignetting to check composition even through a mask.
Previous Pick-up Finder Unit for X-2 is not usable for EOS 80D as it is since finder shape is not identical to the EOS30D or earlier models but possible to use in combination with optional Pick-up Finder Unit 2 (camera side module).
 
*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included when purchasing this product only.
 
Weight: [air] 34 g/1.2 oz.

 

The Finder Window Unit for X-2 is most inexpensive interchangeable finder unit which consists of single waterproof window made of optical glass to access camera's finder. This unit does not have optical function like extending camera's eye-point so only center part of camera's finder is visible through a mask.
 

*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included when purchasing this product only .

 
Weight: [air] 27 g/1.0 oz.

A rear cap for an INON port. When transporting or during storage, this cap protects O-ring and screw mount. The cap is designed to equalize with ambient pressure when transporting in an aircraft.
 

A cap for port mount of a housing to protect O-ring contact surface. The cap is designed to equalize with ambient pressure when transporting in an aircraft.